Good day. Can you help with some fuel consumption numbers?

Why? I do a lot of boating and lots of quick trips. I still work, so going somewhere for a month or weeks is not really possible. Thus, I like to cruise out faster..20mph and drop anchor for a 2-3 days and then head home. Range and fuel consumption is important; Bimini, Fl Keys, etc.



I'm considering holding off on a 356 purchase till I find a diesel (still working, not retired, so I can wait awhile). One just sold, missed it. I h ...

Hello All, Glad to be a member. I own a 280 1993 Carver in Long Beach Cal. I have had the boat 3 years now and I am still looking for a fuse box. If anyone knows please advise. The boat has an upper and lower helm. 2 Volvo Penta engines and outdrives.
I hope to share information. Rick

Hello,

570 carver pilothouse
Does someone know the lifting capacity of the topside winch?

I am re doing the aft deck (with stick on teak) looking good so far, I hope it will be durable.
I am planning to store either a moped or motorcycle up there, construct a table top over the lower part of the bike, install some railings

Thanks

Helping a friend out who has ZF transmissions. Trying to get the old filter out to replace it. Trying to loosen the 6mm bolt on the top of the filter cap, but it doesn't loosen. It's stuck to the cap and will turn the cap when I try to remove the bolt. The cap will turn (fairly easily) but then the tab on the cap hits the housing and won't go farther and the bolt won't loosen. Tried lifting the cap after it's turned left as far as it will go and can't lift it... afraid of breaking off t ...

Hi Everyone,
My name is Peter Q. new to the forum.I got this 2000 Carver 396 ATF Buena Vista yacht. I'm just wondering if there's a holding tank discharge switch somewhere in this yacht?
thank you in advance

Putting my boat in salt water for the first time in a while and need recommendations for anode placements. Checked some of the posts but, there was a lot to dig through and couldn't get the answers I wanted out of 1 or 2 posts. Expecting to put anodes on the shafts and props. Not too sure about the trim tabs. Thanks.

Ok I'm so confused I have an issue with my starboard engine. the distributor is hosed .....The Crusader engine manual says it should have a Mallory yl624av Distributor however i managed to scrape the paint off of it and it says YL670av i need to replace this distributor and i don't know what to get to replace it with. The 624 has a Sierra 18-5313-1 I see nothing for the 670... any help would be appreciated .

Hello all,



Can someone recommend a swim platform davit system for a 650lb zodiac projet 350?



my carver 570 has plenty of deck space as my dingy has currently been sitting centered on the platform.

the hurley h20 claims 350lb capacity, the hurley h30 around 450lb and the hurley h30 plus 725lb

at over $4,000



If that is my only option then "break out another thousand" is under rated.



suggestions or any used hurley h30 plus davits for sale?



also I have put some teak stick on decking on the aft flybri ...

Looking for some advice on an OUPV

I'm considering applying for my "6 pack" OUPV License, but the licensing requirements are clear as mud (per the USCG website, are in the link below). I am assuming that the Gen requirements, and sea service req, both listed above the OUPV license requirements in the linked .pdf chart, must be met to get to the OUPV license/endorsement.
Below the OUPV requirements are "Other requirements" (First Aid and CPR), which seems are not required, followed by "exams" whic ...

Fellow CYO,



I have been a member since 2020.



My name is Larry and I live on Lake Ontario in Ontario. My boat is 2000 404 which we have been upgrading (and enjoying) it since purchasing in 2019. So while I am snowed-in, the work is halted but the planning has continued.



I'm reaching out today because I'm at a loss regarding my foredeck. The previous owner attempted to paint the Port gunnel but the paint was improperly applied and now it is wearing away in places. I suspect the paint was either, not ...