Good morning,



I am new to the forum and this is my first season with my 1986 3607 with gas Crusader Model 350s. I appreciate any assistance with the unusual problem I have been having.



The issue began with some difficult starting on the port motor. It needed to have the throttle wide open to get re-started after the engine was warm.



Several weeks later, the port engine would lose power and stall at idle after warming up for about 20 minutes. After reading the forums, I changed the fuel filters, s ...

Hello!



I am a new to us owner of a 1989 30 Carver Santiago. The Boat is in crazy well maintained condition for a 30 year old craft.



We purchased the boat in Sacramento and I took it on it's "maiden Voyage" to our slip 50± river miles to our slip in Isleton on the Sacramento Delta.



The boat ran perfectly, minus the controls, especially on the port side are pretty stiff.



I want to replace the controls and cables before I take it out again.



Are there any recommendations as to the best control replacemen ...

Hello all: I initially joined this owners forum two years ago but did not use it because boat was in storage. Was unable to sign back in thus became new again. We own a 1989 Carver 2557 Montego Express Cruiser. I will be renovating this lovely old girl this winter. She has a 5.7 litre Mercruiser with an Alpha one (1st gen) stern drive with a 3 blade aluminum prop. All original and with just shy of 500 hours since new. Always kept on a fresh water lake. I purchased this boat two years ago ...

Does a body know if this exhaust nozzle is a factory set up? I have 260 mercs with 4” to 3” exhaust hose on-each manifold they run to mufflers then out the transom to these nozzles that direct the exhaust into the water. Im only making 3000 rpm and am wondering if this is causing excess back pressure. I have gone through fuel system. Carbs and timing.
Thanks
JJ

Went to use the stove top for the first time and it appears inop. Oven works fine but when I select stove top the burners will not warm and the indicator lights do not illuminate. Any help please?

Unwanted that is. A seagull has decided he want to crack open crayfish on my radar and $hit them out. Been there for a couple of weeks now. Will be ordering one of these https://shop.yachtshop.ca/stopgull-stopgull-keeper.html unless someone can give me a better solution short of bringing my shotgun that is.

Well , a sorry state for me I think.....just changed the oil / filters and winterized the genny...boat to come out next week, all the old gas will be sucked out of the tanks as we have not used the boat for much more than a day cottage this year....we seem to have lost the drive for big boat boating, I now like the satisfaction of working on it more than untying the lines. Hopefully next year will see us re-energized or Mr or in our case Mrs Broker here we come.....



Anyone go thru this, an ...

Anyone have an idea on the height difference between stern and bow to block a 1989 Carver 3607 for the winter?Hoping that it will provide sufficient angle to allow any draining of bilge water toward the garboard but maintain a respectable even keel for winter work and engine room cleaning. Will need to find some blocks soon as haul out is only 6 weeks away
Also, how much distance should be between the blocks?
Thanks

Question for you...
My Carver 350 was sunk by a local mechanic last year.
Note: think about over insuring you boat...
It sank to the bottom and considered salvage.
I was able to keep the dinghy and it has Seawise davits.
I plan to sell the dinghy, is it worth the time and expense to remove the davits and sell?

Hello, we purchased a 2002 Carver 450 Voyager Pilothouse earlier this summer. We hired a captain for a day and a half to deliver the boat to our home port and to receive some training. We love this boat! We have been taking day trips practicing our docking skills and learning about the many systems on these boats. Very grateful to all who share on this forum.

JT and Estee