I have a 91 Carver Montego 32'. I have installed the a/c unit under the bench seat between the galley and the aft berth. Does anyone know how to remove the wall behind the bench seat? I need to raise the rear cushion about 3" but can't get it loose from the wall. Also it would make running the ductwork easier. Any help would be appreciated.

Would like to hear what others have had good success with. I have tried quite a few over the years. The last 2 year stint was with Odorlos which I must say worked quite well. I ran out and decided to try the hyped "Noflex Digester". Tried it for the first time this weekend but obviously that is really not enough time to see if it works well.



Lets hear what you have been using and how well it has worked for you. The Odorlos worked 95% of the time, once in a while there would be the standard foul s ...

I'm thinking of installing Wall mounted knife magnet. We like to cook a lot and I don't want my sharp knifes bouncing around in the silverware drawer. I've never used a knife magnet and I'm not sure how secure the knifes stay attached to the magnet while traveling.

Does any one have a knife magnet installed on their boat. How well do they work?

Hello! I've recently discovered that the forward head on our 2002 Carver 356 aft cabin appears to have 2 small holding tanks. the tank closest to the bow does not empty with a pumpout.. there appears to be a valve separating the tanks but the valve won't move and I'm afraid to force it. I'm assuming if the valve could be opened the tank would pump out? Assuming I'm on the right track in the first place....
Any help out there? thanks so much.

Barb
Fearless

Looking for photos of FWC/closed cooling systems on 87/90 3807 aft cabin, with 7.4 merc's. Including the mounting brackets that hold the heat exchanger. Also where the hoses are routed to. Is heat exchanger located on the front of engine by water pumps, or above transmission? Getting boat ready to head south next next winter. Boat has been in fresh water its whole life.

Ron

My 2001 Carver 444 Has a Sharp Microwave / Convection oven M# R820BK I need to replace as the digital readouts are bad. Ive been told dont try and fix but replace. I am having difficulty getting it out. The front bottom foot pads had some tacky substance on them I broke loose but still wont budge. There doesnt seem to be any acces point to get to side bottom or top.

Hello, My aft fuel tanks are dry and I have never used them. My primary qusetion is should they be full is there and issue with the boat planing? What is the best way to manage the fuel burn down? Thanks

Hi all. Hoping to confirm diagnosis.

New to us boat came with reman long block 5.7 thunderbolt 4v engine. On first cruise would not cross 3k rpm. Installing mechanic adjusted timing and idle. Now on acceleration @ 2500 + mild popping noises and still wont cross 3k. Mech says is control module mounted on top of motor.

Wondering if this rings true to experts here.

Thanks for any insight you can share,
Mark

This past weekend a friend was on our boat, he has the same boat only about 3 years older. He was impressed by how quickly our boat came onto plane and cruised about 24.5 MPH at 3400 rpm. He has 7.4's with carbs. I told him I have the same motors with MPI. Later in the evening, back at the dock he asked to see the motors. When he saw the "Bluewater Horizons" he told me these are magnum motors with 380 HP and 490lbs of torque, I thought the only difference from the standard MPI and the Horizons w ...

Okay I am beginning to wonder if I am a jinx to my boat. I moved it to the Gulf Coast of Mississippi a couple weeks ago and then we get a hurricane. Thankfully we didnt get a drop of rain and very light wind as it went east of my boat.
So I am leaving the boat yesterday and realized I didnt have my keys. Yep they are gone and I surmise I left them on my cargo cover of my F150 before I drove away.

Any thoughts on replacing the keys/ switches?

I called Pat in parts at Carver and he was most helpful. ...