Hi,

I have a 1996 Carver 455 and need to replace the refrigerator; can anyone tell me if it can be taken out through the door or how best to get the old one out? Thank You very much!

gentlemen, my toilet tankwacht system on my boat indicate only when it is half full
is there something to be done to re-activate the systemn. Maybe a strong liquid or powder cause i tried with different products that marinas sell especially for that but it did not work

May be somebody has a good suggestion

Michel


mlafortune@canelco.net

Hi All!



I'm still getting to know my '94 Carver 390 CPMY. Great boat, but I've got a few little electrical nigglies. The aft sundeck has a couple of lights in it that don't come on. In the main salon next to the door leading aft, there are two light switches. One turns on salon lights, and the other just a little light on the stairs leading down to the aft stateroom. Does that also turn on the lights out back on the sundeck? I tried putting a voltmeter on the circuit, but got no power. Could the ...

Hello, i have 2001 Cummins 5.9 Deisel. The coolant tanks have corrosion on the bottom of the sides. I cannot determine the exstent of the corrosion on the undeside without remiving the tank. My insticts tell me the corrosion is being caused by disimmiliar metals touching on the bootom where the tank mounts.

Does anyone else have this corrosion and or removed their coolant tanks to repaint? Did the corrosion cover the bottom of tank?

Hi all



We have owned our 2005 56 Voyager for four seasons now. Slept and cruised on her over 240 nights. We mostly cruise

The Straight of Georgia and a bit north. Upgrades:

Espar Hydronic 30 heater ( a must to cruise in NW)

Seawater Recovery water maker

Mastervolt Mass Combi 12/4000 inverter/charger

1200 amp hour battery bank

PC based navigation 15" Touch Screen on bridge and

pasive 23" lower helm monitor. Running Nobeltec TimeZero navigation.

New stereo in main cabin and command bridge

40" LED TV
...

I have a question on the 405's gas engines that I am having surveyed and sea trialed tomorrow. The boat has Crusader 454's in it but I don't know the model # to get maintenance or manual info on the specs of the engines. I have been told that they are 454 XL's, but I am not sure as anything I have read refers to the XL's as having carbs. These engines are fuel injected and appear very clean. Could they be 454 XLi's? While mechanically inclined, I am not sure of the difference between the XL or X ...

So a not so local yard has an over abundance of stands.

Power boat and sailboat stands available, some are Brownell and some are Hostar. Different sizes to choose from, they are rusty but solid. $50 for sailboat stands and $35 for powerboat stands. Two large SP stands 62" to base of screw jack, three SP stands 48",five stands 21" and 4 stands are 13" .

What size an how many would I need for my 1989 2757 Montego?

Jeff Thornton
Negaunee, MI

I have a intermittent jumpy oil pressure gauge on my port side. I have checked the connection at the back on the gauge and every thing is tight. I would like to know where the other end is connected

2001 350 Mariner with 350 MAG MPI.

Thanks
Fraser

Looking at a 2006 Carver 46MY, very clean, one owner, Volvo 480/75P EDC 1600 hrs
Boat is fresh water, Beacon Bay Marina, lots of hours on this yacht, should I be concerned about this?

I have a 2003 466 Carver with Volvo Pena engines and transmissions. While idling the starboard engine will engage. So far the boat has been secured at the dock when this occurs except once while waiting for the fuel dock she started going in circles until i shut the engine off. When it occurs the shifter will move into forward and reverse but the boat only has forward motion until is shut the engine off. I am not sure if this is an engine or transmission issue.



Has anyone had this issue and how ...