Welcome to Carver Yachts Owners Forum
We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com
You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
1997 Mariner 350 question
-
Topic author - Scurvy Dog
- Posts: 10
- Joined: November 28th, 2015, 12:28 pm
- Vessel Info: 1997 350 Mariner
- Location: Macedonia, Ohio
- Has thanked: 1 time
- Been thanked: 2 times
1997 Mariner 350 question
Thanks
Jim and Judi
-
- Deck Hand
- Posts: 84
- Joined: September 21st, 2014, 9:55 am
- Vessel Info: 'After Taxes'
2004 Carver Mariner 360
Lake Simcoe & Georgian Bay,
Ontario, Canada - Location: Lake Simcoe Marina
- Has thanked: 6 times
- Been thanked: 17 times
1997 Mariner 350 question
Why not use a 12-volt tester, (available at any hardware store, or borrow from your friendly mechanic) determine if you have power, then purchase any 12-volt marine quality fixture of your choice and install. Today's choices are immeasurable over what was originally installed, so you shouldn't need to worry about replacing as original part.
My ceiling fixtures are all small round G4 halogen (which I've the replaced almost all halogen G4 type bulbs with LED - not the fixtures, just the bulbs), however over the galley sink, I have one, approximately 12-inch long florescent fixture.
Trust this helps.
Steve
MerCruiser MX 6.2
Lake Simcoe, Ontario
-
Topic author - Scurvy Dog
- Posts: 10
- Joined: November 28th, 2015, 12:28 pm
- Vessel Info: 1997 350 Mariner
- Location: Macedonia, Ohio
- Has thanked: 1 time
- Been thanked: 2 times
1997 Mariner 350 question
Jim
- Ramsport47
- Commander
- Posts: 376
- Joined: February 10th, 2013, 7:13 am
- Vessel Info: 1998 Carver 310 Santego
- Has thanked: 72 times
- Been thanked: 57 times
1997 Mariner 350 question
1998 Carver 310 Santego
T-Merc 350 Mag MPI (300hp)
Port: Cedar Point Marina, Sandusky, Ohio
-
Topic author - Scurvy Dog
- Posts: 10
- Joined: November 28th, 2015, 12:28 pm
- Vessel Info: 1997 350 Mariner
- Location: Macedonia, Ohio
- Has thanked: 1 time
- Been thanked: 2 times
1997 Mariner 350 question
- Ramsport47
- Commander
- Posts: 376
- Joined: February 10th, 2013, 7:13 am
- Vessel Info: 1998 Carver 310 Santego
- Has thanked: 72 times
- Been thanked: 57 times
1997 Mariner 350 question
1998 Carver 310 Santego
T-Merc 350 Mag MPI (300hp)
Port: Cedar Point Marina, Sandusky, Ohio
Return to “Carver Yachts Forum - Model Discussion”
Who is online
Users browsing this forum: No registered users and 73 guests