Welcome to Carver Yachts Owners Forum

We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com

You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

volvo penta 7.4 won't turnover

GAS engine, transmission and generator repair and maintenance discussion forum.
User avatar

Topic author United States of America
Scienceguy
Scurvy Dog
Scurvy Dog
Posts: 17
Joined: July 10th, 2016, 4:20 pm
Vessel Info: 2000 Carver 406 aft cabin
Location: Clayton, NY 1,000 Islands
Been thanked: 2 times

volvo penta 7.4 won't turnover

Postby Scienceguy » September 11th, 2016, 6:45 pm

Hi All,

Here's the worst; an intermittent problem. The stbd engine on my 406 Aft cabin will simply choose not to turnover (of course it turns over and starts nicely when sitting in the sunshine on a beautiful day and you don't have to go out anyway. It's always when you're about to go over the falls............)! It will start with the key on and shorting out the contacts on the solenoid at the starter (that's how I got home).

Wiggling the shift lever to jostle the neutral safety switch doesn't seem to have an effect.

The key switch works according to my multi meter. I thought I had it when I shorted out the wires and it kicked over indicating perhaps poor connections so I then cleaned the terminals and really tightened them down. Turned the key and BOOM. Tried it again a few times and boom problem solved! That is Until I tried starting it the next day!!!! So the key switch seems to be out of the loop.

There are two relays together on each engine. I took the "good relays" out of the Port engine and was going to try them in the stbd engine but needed to make sure it was in its non-functioning mode. While on the bridge I decided to try the port engine without the relays to see what would happen and lo and behold it turned over but wouldn't start. That seems to indicate that they are not needed to get it to turnover.

So what's left? Any ideas?

Thanks a lot

User avatar

United States of America
mjk1040
Admiral
Admiral
Posts: 1518
Joined: July 30th, 2015, 8:15 am
Vessel Info: 1998 355 AC/MY "Deja Vu"
Location: Savannah, NY
Has thanked: 9 times
Been thanked: 242 times

Re: volvo penta 7.4 won't turnover

Postby mjk1040 » September 11th, 2016, 6:53 pm

Something I have seen a lot lately is the wiring harness at the engine being bad, corroded and bad connections. The next time it happens, see if you can get someone to wiggle the harness while the key is in the run position. People sometime step on them or pull on these harnesses and ruin them. Had 2 Volvo engines in carvers do this just this season, a 1989 Santego and a 2001 356 AC/MY, both with Volvo's! Mike
Mike :down:
I'd Rather Be Boating!
1989 Sea Ray Seville
1986 Carver Mariner 32'
1990's Thompson 22' Cuddy Cabin
1990's 4Winns 245 Vista Cruiser
1980's Thompson 19' Open Bow
User avatar

Topic author United States of America
Scienceguy
Scurvy Dog
Scurvy Dog
Posts: 17
Joined: July 10th, 2016, 4:20 pm
Vessel Info: 2000 Carver 406 aft cabin
Location: Clayton, NY 1,000 Islands
Been thanked: 2 times

Re: volvo penta 7.4 won't turnover

Postby Scienceguy » September 11th, 2016, 9:22 pm

Mike,

Thanks. I sure will give that a try the next time it acts up.

Canada
Viper
CYO Supporter
CYO Supporter
Posts: 5984
Joined: July 10th, 2015, 9:58 pm
Vessel Info: 1989 Carver 3807 Aft Cabin
Location: Ontario, Canada
Has thanked: 456 times
Been thanked: 1671 times

Re: volvo penta 7.4 won't turnover

Postby Viper » September 11th, 2016, 9:46 pm

I agree with Mike on the harness. Also consider that the neutral safety switch might be faulty. I can't recall if your application incorporates a slave solenoid or not (I think not) but that would be another pretty common possibility. Have someone at the helm turn the key while you listen in the engine bay. Does anything click when the key is turned to the start position?

Return to “Gas Engines/Transmissions”



Who is online

Users browsing this forum: No registered users and 12 guests