Mariner / Santego?

The is the forum to discuss general information regarding all Carver Yachts.
Post Reply
User avatar
tomschauer
Admiral
Admiral
Posts: 2323
Joined: March 28th, 2016, 10:52 pm
Vessel Info: 1998 Carver 355
Suspicious Fishes !
2022 Kawasaki 310X
Location: upper chesapeake bay
Has thanked: 326 times
Been thanked: 602 times

Re: Mariner / Santego?

Post by tomschauer »

Craig, most likely already has been checked, but the tilt / trim on the outdrives, along with the bellows and shift cable boots on the drives. Also noise from gimbal bearings, would mean they are on the way out. The brearings are realitivley cheap, but the labor is $$$.
User avatar
celmem
Scurvy Dog
Scurvy Dog
Posts: 2
Joined: May 9th, 2019, 10:37 am
Vessel Info: 3467 Santego 1989
330 hp 454 Crusaders
Location: Lake Michigan
Been thanked: 2 times

Re: Mariner / Santego?

Post by celmem »

When I was helping my buddy shop, I was surprised that vision aft was limited in close quarter maneuvering.
To me that's a show stopper.
User avatar
Craig_B
First Mate
First Mate
Posts: 105
Joined: February 14th, 2019, 4:54 pm
Vessel Info: 1988 Carver Santego 3067
Location: Barrie, Ontario
Has thanked: 144 times
Been thanked: 13 times

Re: Mariner / Santego?

Post by Craig_B »

Did the test run today.
I think it went well. Engines fired up promptly and ran smooth.
Both engines made it up to 4500 RPM's with no noise etc.
There are a few minor issues i discovered but I am sure the seller will have those fixed plus any other issues that come up in the final survey.

The owner was not there to do the run but the owner of the marina took us out along with his salesman.
At first the boat would not do much more than 13 knots but after he fiddled with the outdrive angle and the trim tabs he got it up to about 20 knots +. He admitted he was not too familiar with the controls and handling of this particular boat.
Does this sound like an appropriate speed for this boat?

The only other item that has me a bit concerned was the port engine temp did not read at all at low speeds but once we where up on plane it matched the starboard gauge. About 140. I hope its just a gauge issue.
Also noticed some oil leaks that appeared to be from the valve covers and/or fill cap area.
Oil was clean and at the full mark.
User avatar
Craig_B
First Mate
First Mate
Posts: 105
Joined: February 14th, 2019, 4:54 pm
Vessel Info: 1988 Carver Santego 3067
Location: Barrie, Ontario
Has thanked: 144 times
Been thanked: 13 times

Re: Mariner / Santego?

Post by Craig_B »

.............Bump
User avatar
Cooler
Admiral
Admiral
Posts: 1685
Joined: May 22nd, 2018, 12:09 pm
Vessel Info: 1995 Carver 330 Mariner
Twin 350XL Crusaders
Home port: Menominee, MI
Location: Green Bay, WI
Has thanked: 68 times
Been thanked: 414 times

Re: Mariner / Santego?

Post by Cooler »

Craig - yes, that speed sounds about right at 3200 to 3400 RPM. WOT at 4500 is normal. The thermostat could have been stuck wide open for that port side engine, and then recovered when some throttle got pushed up. As long as it did not get hotter than the other engine, should be alright. Minor evidence of oil leaks is normal for engines 30 years old. Looks like it is coming together! 8-) er
Cooler By The Lake
( All weather people have to say this on air, near lakes )
User avatar
Craig_B
First Mate
First Mate
Posts: 105
Joined: February 14th, 2019, 4:54 pm
Vessel Info: 1988 Carver Santego 3067
Location: Barrie, Ontario
Has thanked: 144 times
Been thanked: 13 times

Re: Mariner / Santego?

Post by Craig_B »

Still waiting on the remainder of the survey. The weather here has been crappy which has apparently delayed him quite a but. :(

Says he will call me tomorrow and if all is good we will sign the paperwork the next day. :D

Thanks to all that took the time to help us out.
User avatar
ColRon
Admiral
Admiral
Posts: 581
Joined: April 24th, 2017, 6:06 pm
Vessel Info: 1989 Carver Santego 3867
“Escape Plan”
Location: Murray, KY
Has thanked: 77 times
Been thanked: 157 times

Re: Mariner / Santego?

Post by ColRon »

Craig_B wrote:QR_BBPOST Still waiting on the remainder of the survey. The weather here has been crappy which has apparently delayed him quite a but. :(
Have an update on the remainder of your survey? Inquiring minds would live to know! :-D
Ron
1989 Carver Santego 3867
“Escape Plan”
Murray, KY

:usa:
User avatar
Craig_B
First Mate
First Mate
Posts: 105
Joined: February 14th, 2019, 4:54 pm
Vessel Info: 1988 Carver Santego 3067
Location: Barrie, Ontario
Has thanked: 144 times
Been thanked: 13 times

Re: Mariner / Santego?

Post by Craig_B »

Just got the final report this morning.
Overall he says the boat is in above average condition for its vintage. :clap:

A few minor things need to be addressed but the seller said he will be attending to those issues.
User avatar
RGrew176
Admiral
Admiral
Posts: 6652
Joined: August 17th, 2015, 4:07 am
Vessel Info: 2023 SunTracker Party Barge 22 DLX
Location: Southgate, MI.
Has thanked: 72 times
Been thanked: 470 times

Re: Mariner / Santego?

Post by RGrew176 »

Sounds good.
Rick Grew

2025 Godfrey Xperience 2286 SFLX

2004 Past Commodore
West River Yacht & Cruising Club
User avatar
ColRon
Admiral
Admiral
Posts: 581
Joined: April 24th, 2017, 6:06 pm
Vessel Info: 1989 Carver Santego 3867
“Escape Plan”
Location: Murray, KY
Has thanked: 77 times
Been thanked: 157 times

Re: Mariner / Santego?

Post by ColRon »

Craig_B, sounds like we will be adding another proud Santego owner to the fold! :down:
Ron
1989 Carver Santego 3867
“Escape Plan”
Murray, KY

:usa:
Post Reply