Welcome to Carver Yachts Owners Forum
We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com
You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
Water Temperature Senders
-
jms642
Topic author
- Scurvy Dog
- Posts: 2
- Joined: May 10th, 2020, 12:28 pm
- Vessel Info: '86 4207 ACMY
350 Crusaders
Camp Lejeune, NC - Location: Camp Lejeune, NC
- Has thanked: 13 times
Water Temperature Senders
My 350 Crusaders each have two water temp sending units and my boat has dual stations. After a recent overheating incident, I replaced the thermostat, water pump, and senders. Then the ignition fuse started blowing. This morning I disconnected the single wires from each of the new senders and bingo, no more fuse problems. Of course, I don't have working water temp gauges either. I'm wondering if anyone knows whether those senders should be for dual station? I assumed that two identical units with one wire each were only serving one gauge. I just bought two new dual station senders, but hesitate to install them without asking one of you really smart folks. Thanks for any advice!
'86 4207 ACMY
350 Crusaders
Camp Lejeune, NC
350 Crusaders
Camp Lejeune, NC
-
bud37
- Admiral
- Posts: 4865
- Joined: April 23rd, 2015, 10:22 pm
- Has thanked: 579 times
- Been thanked: 1210 times
Re: Water Temperature Senders
Welcome to the forum....
Is one of those a sender and the other an alarm switch for each engine? Dual stations should always have dual station senders to match the gages. Don't use thread tape when installing....ground thru the block.
Did you match the numbers of the senders and switches you took out with the new ones ? Hopefully you still have the old ones.
My guess here, hard to say without seeing for me.
Is one of those a sender and the other an alarm switch for each engine? Dual stations should always have dual station senders to match the gages. Don't use thread tape when installing....ground thru the block.
Did you match the numbers of the senders and switches you took out with the new ones ? Hopefully you still have the old ones.
My guess here, hard to say without seeing for me.
The above is strictly my opinion.
-
Viper
- CYO Supporter
- Posts: 5975
- Joined: July 10th, 2015, 9:58 pm
- Vessel Info: 1989 Carver 3807 Aft Cabin
- Location: Ontario, Canada
- Has thanked: 455 times
- Been thanked: 1671 times
Re: Water Temperature Senders
Welcome aboard.
On each sender post where the sender wire is hooked up, in some cases there should be a small non metallic washer to prevent the sender wire from touching the grounded housing. The post is isolated from the grounded metal housing but if the washer is missing, your sender wire connector is likely shorting to ground and blowing your fuse. Check to ensure the connector on the wire is not in contact with the metal housing and let us know.
On each sender post where the sender wire is hooked up, in some cases there should be a small non metallic washer to prevent the sender wire from touching the grounded housing. The post is isolated from the grounded metal housing but if the washer is missing, your sender wire connector is likely shorting to ground and blowing your fuse. Check to ensure the connector on the wire is not in contact with the metal housing and let us know.
-
jms642
Topic author
- Scurvy Dog
- Posts: 2
- Joined: May 10th, 2020, 12:28 pm
- Vessel Info: '86 4207 ACMY
350 Crusaders
Camp Lejeune, NC - Location: Camp Lejeune, NC
- Has thanked: 13 times
Re: Water Temperature Senders
bud37: thanks a million for the reply. The old ones (original = 33 years old) broke when I took them out, so I'm stuck with new ones. Will install the dual station senders and see how it goes.
Viper: Thanks so much. That's the ticket. These new ones (from West Marine) did not come with non-metallic washers. Clearly, this is why the fuse was blowing. I'll pick up a couple and try again.
You fellows are mighty kind to help!
Viper: Thanks so much. That's the ticket. These new ones (from West Marine) did not come with non-metallic washers. Clearly, this is why the fuse was blowing. I'll pick up a couple and try again.
You fellows are mighty kind to help!
'86 4207 ACMY
350 Crusaders
Camp Lejeune, NC
350 Crusaders
Camp Lejeune, NC
-
Viper
- CYO Supporter
- Posts: 5975
- Joined: July 10th, 2015, 9:58 pm
- Vessel Info: 1989 Carver 3807 Aft Cabin
- Location: Ontario, Canada
- Has thanked: 455 times
- Been thanked: 1671 times
Re: Water Temperature Senders
Keep us posted. The 4207 is a nice boat by the way, no shortage of room there 
I bet the Crusaders look small in that engine compartment.
I bet the Crusaders look small in that engine compartment.Who is online
Users browsing this forum: No registered users and 40 guests
Sponsors