Carver 346 fuel transfer

GAS engine, transmission and generator repair and maintenance discussion forum.
User avatar
Pha8
Scurvy Dog
Scurvy Dog
Posts: 34
Joined: September 28th, 2024, 1:15 am
Vessel Info: 2002 Carver 346
Location: Toronto
Has thanked: 32 times
Been thanked: 5 times

Carver 346 fuel transfer

Post by Pha8 »

2002 Carver 346
Is their a way to transfer fuel from the STBD tank to the Port tank? Not seeing any switches or pumps?

Cheers
User avatar
bud37
Admiral
Admiral
Posts: 5182
Joined: April 23rd, 2015, 10:22 pm
Has thanked: 604 times
Been thanked: 1312 times

Re: Carver 346 fuel transfer

Post by bud37 »

If your boat is gas powered then I seriously doubt there will be a pump and hoses factory installed to do that. That was generally a diesel option for safety reasons.

Do you have some valves that allow lets say, the port engine to pull fuel from the starboard fuel tank or does each engine just pull from it respective side only ?
FWIW.....The above is just my opinion.
User avatar
buster53
Admiral
Admiral
Posts: 1170
Joined: May 12th, 2017, 10:41 am
Vessel Info: 2001, Carver 356
Location: Gwynn’s Island, VA
Has thanked: 10 times
Been thanked: 285 times

Re: Carver 346 fuel transfer

Post by buster53 »

As mentioned, very unlikely you have a fuel transfer pump. On my 356, I do have switches I can use to pull from either of my 3 tanks (2 saddle tanks plus aux tank in the swim platform) to feed either engine, so that is a work around to even out fuel levels. Only one set in stone…the genset only pulls from the port tank, and cannot access the other 2 tanks.
User avatar
Pha8
Scurvy Dog
Scurvy Dog
Posts: 34
Joined: September 28th, 2024, 1:15 am
Vessel Info: 2002 Carver 346
Location: Toronto
Has thanked: 32 times
Been thanked: 5 times

Re: Carver 346 fuel transfer

Post by Pha8 »

bud37 wrote:QR_BBPOST If your boat is gas powered then I seriously doubt there will be a pump and hoses factory installed to do that. That was generally a diesel option for safety reasons.

Do you have some valves that allow lets say, the port engine to pull fuel from the starboard fuel tank or does each engine just pull from it respective side only ?
6.2L Mercurisers
Cant see any valves, but maybe something hidden?
User avatar
buster53
Admiral
Admiral
Posts: 1170
Joined: May 12th, 2017, 10:41 am
Vessel Info: 2001, Carver 356
Location: Gwynn’s Island, VA
Has thanked: 10 times
Been thanked: 285 times

Re: Carver 346 fuel transfer

Post by buster53 »

Since our boats are similar…
My fuel switches are mounted on the forward firewall in front of the port engine. Of course, it’s possible you don’t have any at all.
FWIW, I used to have a 3807 and our switches were mounted inside the hanging closet in the aft stateroom. My point…Carver was very creative in where they placed switches, valves, bilge access points, etc. and often, a search had to be made to find things.
User avatar
Pha8
Scurvy Dog
Scurvy Dog
Posts: 34
Joined: September 28th, 2024, 1:15 am
Vessel Info: 2002 Carver 346
Location: Toronto
Has thanked: 32 times
Been thanked: 5 times

Re: Carver 346 fuel transfer

Post by Pha8 »

buster53 wrote:QR_BBPOST Since our boats are similar…
My fuel switches are mounted on the forward firewall in front of the port engine. Of course, it’s possible you don’t have any at all.
FWIW, I used to have a 3807 and our switches were mounted inside the hanging closet in the aft stateroom. My point…Carver was very creative in where they placed switches, valves, bilge access points, etc. and often, a search had to be made to find things.
Yes they are masters at hiding stuff. I will now have to go on an easter egg hunt.

Cheers
User avatar
Pha8
Scurvy Dog
Scurvy Dog
Posts: 34
Joined: September 28th, 2024, 1:15 am
Vessel Info: 2002 Carver 346
Location: Toronto
Has thanked: 32 times
Been thanked: 5 times

Re: Carver 346 fuel transfer

Post by Pha8 »

buster53 wrote:QR_BBPOST Since our boats are similar…
My fuel switches are mounted on the forward firewall in front of the port engine. Of course, it’s possible you don’t have any at all.
FWIW, I used to have a 3807 and our switches were mounted inside the hanging closet in the aft stateroom. My point…Carver was very creative in where they placed switches, valves, bilge access points, etc. and often, a search had to be made to find things.
Yes they are masters at hiding stuff. I will now have to go on an easter egg hunt.

Cheers
Carverlvr2
First Mate
First Mate
Posts: 161
Joined: September 15th, 2024, 10:13 pm
Vessel Info: 2004 Carver 366, VP 8.1’s
1992 Carver 33, Crusader 7.4’s
1979 Searay Sundancer 260
Location: Shelbyville, IL
Been thanked: 25 times

Re: Carver 346 fuel transfer

Post by Carverlvr2 »

I have your sister ship, the 366. Same boat, different floor plan. I have no fuel valves or transfers. Carver seems to have dropped that from the 33/355/356 series.
User avatar
km1125
Admiral
Admiral
Posts: 3657
Joined: February 28th, 2017, 6:04 pm
Has thanked: 81 times
Been thanked: 1114 times

Re: Carver 346 fuel transfer

Post by km1125 »

Pha8 wrote:QR_BBPOST

Yes they are masters at hiding stuff. I will now have to go on an easter egg hunt.

Cheers
On the 3607, the fuel selector valves are underneath the lowest step going down into the salon. It hinges up for access to those valves. (the master DC power 1/2/all switch is also there). If someone didn't tell you, you'd have a heck of a time finding those, but crawling around in the engine room and following hoses and cables would give you a clue.

I'd be surprised if a boat as big as a 346 didn't have some type of fuel selection valves, even if just an on/off for each engine.
Viper
CYO Supporter
CYO Supporter
Posts: 6266
Joined: July 10th, 2015, 9:58 pm
Vessel Info: 1989 Carver 3807 Aft Cabin
Location: Ontario, Canada
Has thanked: 475 times
Been thanked: 1791 times

Re: Carver 346 fuel transfer

Post by Viper »

Ya I’d be surprised too if you didn’t have valves. Typically they’re on the engine compartment forward bulkhead in front of the engines, mine are in the aft stateroom closet. If they’re not obvious in the engine room, follow the fuel lines from the engines or fuel tanks as km mentioned.

You won’t have a transfer pump from factory but who knows what a previous owner might have done. If you do see one, I’d remove it because it’s not uncommon for those to leak. That’s not so bad in a diesel application but very dangerous in a gasoline one.
Post Reply