Bilge paint

Anything related to the operation of your boat. Steering, Bilge Pumps, thru-hulls, bottom paint, etc.
Post Reply
User avatar
paulr
First Mate
First Mate
Posts: 130
Joined: September 27th, 2022, 9:36 pm
Vessel Info: 396 CY Aft Cabin 2001 8.1 Crusaders
Location: South Jersey, LBI
Has thanked: 56 times
Been thanked: 32 times

Bilge paint

Post by paulr »

Hello,
I am doing some refreshing my 2001 Carver 396. I would like to paint some portions of my bilge. I would like to match the orginal flat grey paint. I see the availible bilge paint out there seems to be gloss. Does anyone one know what paint may match the original flat gray paint?
Any information wouls be appreciated.
Thanks
User avatar
Cooler
Admiral
Admiral
Posts: 1685
Joined: May 22nd, 2018, 12:09 pm
Vessel Info: 1995 Carver 330 Mariner
Twin 350XL Crusaders
Home port: Menominee, MI
Location: Green Bay, WI
Has thanked: 68 times
Been thanked: 414 times

Re: Bilge paint

Post by Cooler »

Carver used a lot of Interlux brand products at that time. One reason they used grey, is so you could see evidence of any stress cracking easily. Especially near the stringers and motor mounts. Don't get too thick, because you may see cracks that are paint related rather than stress evidence. Good luck! 8-) er
Cooler By The Lake
( All weather people have to say this on air, near lakes )
Viper
CYO Supporter
CYO Supporter
Posts: 6266
Joined: July 10th, 2015, 9:58 pm
Vessel Info: 1989 Carver 3807 Aft Cabin
Location: Ontario, Canada
Has thanked: 475 times
Been thanked: 1791 times

Re: Bilge paint

Post by Viper »

I suspect what you're looking at is gelcoat, not paint. I don't know what colour was used but you could get a colour match done. Gelcoat is the best way to go, it's more expensive but will outlast paint. You could use paint though, it's cheaper and easier to work with. The key is proper prep or it'll eventually peel/flake off.

For gelcoat, contact Spectrum Color in Florida, they carry Carver colours. They probably have the specs for what Carver used and can mix a batch if they don't have it on the shelf..... https://spectrumcolor.com/
User avatar
bud37
Admiral
Admiral
Posts: 5182
Joined: April 23rd, 2015, 10:22 pm
Has thanked: 604 times
Been thanked: 1312 times

Re: Bilge paint

Post by bud37 »

I believe it is possible to add/mix in a deglosser to gloss paint....check with the supplier as to what to use for the brand you select.

I agree though, the bilge will have to be prepped very well ( read very clean).
FWIW.....The above is just my opinion.
User avatar
km1125
Admiral
Admiral
Posts: 3657
Joined: February 28th, 2017, 6:04 pm
Has thanked: 81 times
Been thanked: 1114 times

Re: Bilge paint

Post by km1125 »

When I had my boat, you could see evidence around things like the bulkheads to show they sprayed the grey paint in the bilge. I bought some Grey Interlux Bilgecoat and it matched very well, even though the old paint was over a decade old. The color was the same but you could definitely tell where there was old paint and new paint.

Years later I got some more Grey bilge paint (different brand - forgot who now) but it turned out to be a lighter shade so it would not have matched, but luckily the areas I was repainting were in the aft cabin so you couldn't really tell that it was lighter than the engine room.
Post Reply