Hello all! I have twin 454's on my '86 4207. Are the Edelbrock Performer intake manifolds factory stock on them? I have to replace both of them due to corrosion holes by the water temp. sending units.
Thanks!
Intake Manifolds 454ci
-
Ramsport47
- Commander
- Posts: 376
- Joined: February 10th, 2013, 7:13 am
- Vessel Info: 1998 Carver 310 Santego
- Has thanked: 72 times
- Been thanked: 59 times
Re: Intake Manifolds 454ci
No, they are not standard, or even offered from the engine manufacturer. My guess is someone installed them to try to get better performance out of the boat. The originals are cast iron, although I'm not sure they are still available, so you may have to go with Edelbrocks again.
Kenny
1998 Carver 310 Santego
T-Merc 350 Mag MPI (300hp)
Port: Cedar Point Marina, Sandusky, Ohio
1998 Carver 310 Santego
T-Merc 350 Mag MPI (300hp)
Port: Cedar Point Marina, Sandusky, Ohio
-
waybomb
- CYO Moderator
- Posts: 2745
- Joined: February 5th, 2013, 9:24 pm
- Vessel Info: 1995 Boston Whaler Rage15
1987 3697 Carver Mariner
1988 Cougar 46 Kevlar Vee offshore
1969 15' Glasspar / 1967 Johnson Electromatic 85 - Location: Saint Joseph,Mi
- Has thanked: 69 times
- Been thanked: 492 times
Re: Intake Manifolds 454ci
Had a 4207 with big blocks.
That boat needed way more than just intake manifolds to make it right.
Still looking for a 4207 that somebody repowered with 500 cats. That would make my day.
That boat needed way more than just intake manifolds to make it right.
Still looking for a 4207 that somebody repowered with 500 cats. That would make my day.
Thanks
Fred
1969 Glaspar Avalon /1967 Johnson Electromatic 85
1987 Carver Mariner
1988 Cougar Kevlar 46' with triple blown 572 ci
1995 Boston Whaler Rage
Past - 1988 2807, 1989 4207 Aft
Fred
1969 Glaspar Avalon /1967 Johnson Electromatic 85
1987 Carver Mariner
1988 Cougar Kevlar 46' with triple blown 572 ci
1995 Boston Whaler Rage
Past - 1988 2807, 1989 4207 Aft
-
Viper
- CYO Supporter
- Posts: 6266
- Joined: July 10th, 2015, 9:58 pm
- Vessel Info: 1989 Carver 3807 Aft Cabin
- Location: Ontario, Canada
- Has thanked: 475 times
- Been thanked: 1791 times
-
waybomb
- CYO Moderator
- Posts: 2745
- Joined: February 5th, 2013, 9:24 pm
- Vessel Info: 1995 Boston Whaler Rage15
1987 3697 Carver Mariner
1988 Cougar 46 Kevlar Vee offshore
1969 15' Glasspar / 1967 Johnson Electromatic 85 - Location: Saint Joseph,Mi
- Has thanked: 69 times
- Been thanked: 492 times
Re: Intake Manifolds 454ci
Been looking since we sold our 4207.
I had the pleasure of piloting an 86 4207 that was repowered with 500s.
That boat came alive.
I had the pleasure of piloting an 86 4207 that was repowered with 500s.
That boat came alive.
Thanks
Fred
1969 Glaspar Avalon /1967 Johnson Electromatic 85
1987 Carver Mariner
1988 Cougar Kevlar 46' with triple blown 572 ci
1995 Boston Whaler Rage
Past - 1988 2807, 1989 4207 Aft
Fred
1969 Glaspar Avalon /1967 Johnson Electromatic 85
1987 Carver Mariner
1988 Cougar Kevlar 46' with triple blown 572 ci
1995 Boston Whaler Rage
Past - 1988 2807, 1989 4207 Aft
Sponsors