I have a 2000 396 and the water tank fill ring chrome trim ring on the sb side got knocked off. Does anyone know where to find a replacement trim ring? It is very small and I could not find one checking online suppliers. Any help is most appreciated.

Hi,



New to the forum. Just bought my first boat, a 350 Mariner. I'm replacing a lot of the interior fixtures - shower sump, cabin lights, radio/tv, cabinet hinges etc. but I'm stuck trying to replace the internal salon speakers either side of the rear door, under the external stairs at either side of the boat. These have a plastic cowling that is flush against the internal fiberglass and I can't see any way of removing it.



Any help is appreciated,



Colin.

New member, first post - glad to be joining your community. I'm dealing on a 1991 Carver Californian 4509 (45 ft) ACMY. On the sea trial, the 375 hp CAT 3208 TA's would only make 2400 WOT RPM. The surveyor says 2800 is the desired figure. The props on this boat are rebuilds and the surveyor's not convinced they are correctly pitched. The owner has a pair of new in-the-box spares from which I'm trying to get dimensions for comparison to those on the boat. Carver is defunct so I'm asking here if ...

Good morning! We own a 97' 355AC w/ Crusader 454 XLi's, throttle body injected. My starboard engine is showing 80psi at the helm regardless of the engine speed when the engine runs. The gauge itself is working, I swapped the port and starboard gauges this past weekend. I'd like to replace the sender on engine but I'm not sure if I need a single station send or dual station sender. I only have one helm, the flybridge. Any suggestions would be apprecaited.

Cheers!

Hull Serial number,
Hi guys and gals. It has been a while since I have enjoyed your company and help here on the forum. Unfortunately, I am now at a point where I am having to sell my old girl. It is a 1982 3007 aft-cabin. I need to provide a hull serial number in order to list it. I can't for the life of me find it anywhere. Can any of you tell me where on my ship it is located? Many thanks in advance for any HELP!

Hey there Carver owners, this is our first big block 454 engined Carver, and I was wondering if anyone had any idea of the best cruising speed for the 36 aft cabin? Right now we’re cruising at about 2000 RPM and getting about 8-9 knots depending on the tides, burning about 12 gph, Has anyone found a faster cruising speed, such as on plane at 3-3200 RPM any more economical than what we’re doing now? I know that our 42 aft cabin with the 375hp Cats was got about 9knots at 1800RPM burning about 6gp ...

Hello all. Joined the forum not long ago after having my bid accepted on a 03 360 sport sedan, so this is my first post. Wondering though if it may also be my last as I just got my survey results back.



Quick summary: boat has the gas Volvo penta 8.1s at 375 hp with about 400 hrs each. During the sea trial (other than the starboard engine shredding a belt which got replaced at the haul out) they ran great. Started right up. Sound good, no skipping/hunting. 20 knots at 3500 rpm. Got a knock in on ...

Over the last month or so my bow thruster has been getting weaker and weaker to the point where it has very little power left. Obviously something is not right. Voltage and power to the unit is fine. Anyone know where I should start? Clueless on thrusters but guess I will learn quickly.

Thruster is a Side-Power unit. Found this but not helpful for my issue.


https://www.youtube.com/watch?v=jk9z8XxJjOU


Also found this which may be applicable to me but would like some confirmation.




Also found this which may be applicable to me but would like some confirmation.

...

Hi all, signed up a couple years ago after purchasing our 2000 Voyager 374. Just stopping in to introduce myself. I have a few things needing replaced or repaired so i'll be searching around and possibly posting my questions or problems if i can't find them via search.

hi all looking for shower door for 86 3207 any condition
thanks Scotty