Installed the trim around the shelves. Have to cut the top piece yet. TV will go in the big section
Put a coat on the stairs. Trying to decied if I should put a non-skid additive or get some non-skid pads to put down when we a swimming
Welcome to Carver Yachts Owners Forum
We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com
You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
Carver 3207 Revised - 2015 projects & bow thruster
-
Mkemper
Topic author - Deck Hand
- Posts: 96
- Joined: February 18th, 2013, 9:04 am
- Vessel Info: 86' carver 3207 Aft
[IMG]http://i1238.photobucket.com/albums/ff498/mjkkemper/null_zps98e8d64b.jpg[/IMG] - Been thanked: 8 times
Re: Carver 3207 Revised
Sliding in the modular units.
Installed the trim around the shelves. Have to cut the top piece yet. TV will go in the big section
Put a coat on the stairs. Trying to decied if I should put a non-skid additive or get some non-skid pads to put down when we a swimming
Installed the trim around the shelves. Have to cut the top piece yet. TV will go in the big section
Put a coat on the stairs. Trying to decied if I should put a non-skid additive or get some non-skid pads to put down when we a swimming
-
AaHubb
- Commander
- Posts: 315
- Joined: February 16th, 2013, 5:46 pm
- Vessel Info: '99 404 CPMY
my twin diesel pusher - Location: Kennewick, Wa
- Has thanked: 15 times
- Been thanked: 61 times
Re: Carver 3207 Revised
Those shelves are going to be a nice addition and look great. I have found non-skid to be a real dirt collector, how about a towel for a temp door mat.
'99 404 CPMY
SeaDragon
SeaDragon
-
Mkemper
Topic author - Deck Hand
- Posts: 96
- Joined: February 18th, 2013, 9:04 am
- Vessel Info: 86' carver 3207 Aft
[IMG]http://i1238.photobucket.com/albums/ff498/mjkkemper/null_zps98e8d64b.jpg[/IMG] - Been thanked: 8 times
Re: Carver 3207 Revised
I ran a chase from the one cabinet to the other. The back of the large cabinet is the case for the engine vent so I did not want any electrical in there as well as making sure the compartment is sealed
Ready for a finish!
Ready for a finish!
-
Mkemper
Topic author - Deck Hand
- Posts: 96
- Joined: February 18th, 2013, 9:04 am
- Vessel Info: 86' carver 3207 Aft
[IMG]http://i1238.photobucket.com/albums/ff498/mjkkemper/null_zps98e8d64b.jpg[/IMG] - Been thanked: 8 times
Re: Carver 3207 Revised
I got the carpet installed
Hooked up the Batteries to see how the new panels light looked
Ready to go in this Wednesday
Hooked up the Batteries to see how the new panels light looked
Ready to go in this Wednesday
-
waybomb
- CYO Moderator
- Posts: 2497
- Joined: February 5th, 2013, 9:24 pm
- Vessel Info: 1995 Boston Whaler Rage15
1987 3697 Carver Mariner
1988 Cougar 46 Kevlar Vee offshore
1969 15' Glasspar / 1967 Johnson Electromatic 85 - Location: Saint Joseph,Mi
- Has thanked: 53 times
- Been thanked: 425 times
Re: Carver 3207 Revised
Looking good!
Thanks
Fred
1969 Glaspar Avalon /1967 Johnson Electromatic 85
1987 Carver Mariner
1988 Cougar Kevlar 46' with triple blown 572 ci
1995 Boston Whaler Rage
Past - 1988 2807, 1989 4207 Aft
Fred
1969 Glaspar Avalon /1967 Johnson Electromatic 85
1987 Carver Mariner
1988 Cougar Kevlar 46' with triple blown 572 ci
1995 Boston Whaler Rage
Past - 1988 2807, 1989 4207 Aft
-
iceman3500
- Scurvy Dog
- Posts: 19
- Joined: March 7th, 2013, 9:31 pm
- Vessel Info: 1987 Carver 3207
Re: Carver 3207 Revised
Is that just one piece of carpet? If not, what did you do for the hatches? The cabinets turned out awesome. You mention you didn't want any electrical below decks. Would it be a problem wiring up a 12 volt car amp, etc under there? The wife will lose her mind if I bolt any electronics visible inside the salon. Thanks.
-
Mkemper
Topic author - Deck Hand
- Posts: 96
- Joined: February 18th, 2013, 9:04 am
- Vessel Info: 86' carver 3207 Aft
[IMG]http://i1238.photobucket.com/albums/ff498/mjkkemper/null_zps98e8d64b.jpg[/IMG] - Been thanked: 8 times
Re: Carver 3207 Revised
iceman3500 wrote:Is that just one piece of carpet? If not, what did you do for the hatches? The cabinets turned out awesome. You mention you didn't want any electrical below decks. Would it be a problem wiring up a 12 volt car amp, etc under there? The wife will lose her mind if I bolt any electronics visible inside the salon. Thanks.
Yes just one piece of carpet. You just need to roll it up to gain access to the hatch. In regarding the electrical what I meant was that behind the forward large section for the TV is the chase for the venting for the engines. I did not want to put a electrical outlet in that section that would protrude into this vent chase. So a ran a pvc pipe chase (with blk cap) through the electrical panel section to the other shelving section in which I have a plug.
-
Mkemper
Topic author - Deck Hand
- Posts: 96
- Joined: February 18th, 2013, 9:04 am
- Vessel Info: 86' carver 3207 Aft
[IMG]http://i1238.photobucket.com/albums/ff498/mjkkemper/null_zps98e8d64b.jpg[/IMG] - Been thanked: 8 times
Re: Carver 3207 Revised
Well I think it's time to enjoy the summer. Thought I'd finish up with some before and after shots.
Different boat but same setup
After
Green carpet just like you see in Brady bunch household
After
Different boat but same setup
After
Green carpet just like you see in Brady bunch household
After
Return to “The Project Center”
Who is online
Users browsing this forum: No registered users and 20 guests
Sponsors