Breaker Panel

Discussion of batteries, chargers, wiring, generators, distribution panels, battery switches, etc.
Post Reply
User avatar
jonest7
Scurvy Dog
Scurvy Dog
Posts: 2
Joined: July 13th, 2021, 6:58 am
Vessel Info: 1986 Mariner 32
Location: Georgian Bay

Breaker Panel

Post by jonest7 »

I have a 1986 32 Mariner with a windlass switch issue. I cannot find the breaker.
I have been told that there may be another panel other than the main panel in the cabin.
Appreciate any help
User avatar
Midnightsun
CYO Supporter
CYO Supporter
Posts: 2984
Joined: March 27th, 2016, 2:27 pm
Vessel Info: The Midnight Sun
2007 41CMY
Volvo D6-370's
Location: Montreal, Canada
Has thanked: 272 times
Been thanked: 1193 times

Re: Breaker Panel

Post by Midnightsun »

You wont find another panel however you should find a breaker similar to this. Most likely located near the main on off battery switch.
https://www.amazon.ca/ZOOKOTO-Circuit-B ... B07GCVSBNP
Cheers, Hans
2007 Carver 41 CMY
Twin Volvo D6-370's
Montreal, Canada
Midnight Sun I Photos
User avatar
bud37
Admiral
Admiral
Posts: 5182
Joined: April 23rd, 2015, 10:22 pm
Has thanked: 604 times
Been thanked: 1312 times

Re: Breaker Panel

Post by bud37 »

What is the windlass make ? Have you seen a fairly large red button...push on/pull off, that is the breaker if maxwell.
FWIW.....The above is just my opinion.
User avatar
Midnightsun
CYO Supporter
CYO Supporter
Posts: 2984
Joined: March 27th, 2016, 2:27 pm
Vessel Info: The Midnight Sun
2007 41CMY
Volvo D6-370's
Location: Montreal, Canada
Has thanked: 272 times
Been thanked: 1193 times

Re: Breaker Panel

Post by Midnightsun »

Maxwell must have changed breaker type as I have had 2 maxwell units and both were like the link I posted above. Regardless, you are looking for an in-line breaker of some sort, not a panel.
Cheers, Hans
2007 Carver 41 CMY
Twin Volvo D6-370's
Montreal, Canada
Midnight Sun I Photos
User avatar
bud37
Admiral
Admiral
Posts: 5182
Joined: April 23rd, 2015, 10:22 pm
Has thanked: 604 times
Been thanked: 1312 times

Re: Breaker Panel

Post by bud37 »

A lot of the earlier models came from the factory with no windlass.......so it could be a retro fit installation, so the breaker could be anything, anywhere depending on the windlass maker, size, the installer and the year it was installed. For sure it will be in the main feed cable.

Sorry not much help...the hunt is on... :-D
FWIW.....The above is just my opinion.
User avatar
tomschauer
Admiral
Admiral
Posts: 2323
Joined: March 28th, 2016, 10:52 pm
Vessel Info: 1998 Carver 355
Suspicious Fishes !
2022 Kawasaki 310X
Location: upper chesapeake bay
Has thanked: 326 times
Been thanked: 602 times

Re: Breaker Panel

Post by tomschauer »

There is also the possibility that someone installed it without a breaker. If so, I would install one.
User avatar
jonest7
Scurvy Dog
Scurvy Dog
Posts: 2
Joined: July 13th, 2021, 6:58 am
Vessel Info: 1986 Mariner 32
Location: Georgian Bay

Re: Breaker Panel

Post by jonest7 »

Thanks everyone for the ideas. I will keep searching. I have a powerwinch model 612.
User avatar
bud37
Admiral
Admiral
Posts: 5182
Joined: April 23rd, 2015, 10:22 pm
Has thanked: 604 times
Been thanked: 1312 times

Re: Breaker Panel

Post by bud37 »

Powerwinch......have a look for maybe something like this in the main cable from the battery.....it is a pic of their 25amp breaker they used on some models....
P1027600AJ-2__53617.1596815808.jpg
You do not have the required permissions to view the files attached to this post.
FWIW.....The above is just my opinion.
User avatar
km1125
Admiral
Admiral
Posts: 3657
Joined: February 28th, 2017, 6:04 pm
Has thanked: 81 times
Been thanked: 1114 times

Re: Breaker Panel

Post by km1125 »

Do some troubleshooting first, because you might have two different circuits. On my boat, which was similar vintage and an aftermarket winch install, there was the main circuit from the batteries to the winch solenoids that was protected by a big breaker by the batteries, but there was another circuit - the control circuit - that fed the switches from sources at each helm and there was a separate smaller breaker in the panel for this circuit.

Check to see if you have any voltage on the big solenoids by the winch. If you do, then start troubleshooting the switch circuit(s) to see where they are fed from.
User avatar
Phrancus
Commander
Commander
Posts: 395
Joined: October 1st, 2020, 10:03 am
Vessel Info: Sold: Carver 26 Command Bridge / 280 sedan 1992.
Location: Netherlands, Europe
Has thanked: 16 times
Been thanked: 136 times
Contact:

Re: Breaker Panel

Post by Phrancus »

in my 1991 someone used a house type breaker high up inside the lower helm closet.... and nothing from battery in the engine bay to that spot :clap:

it works as an off/on switch but doubt that it will do much quick enough before it burns when stuck. Replaced the solenoids for a modern single block with remotes, as the foot switches were toast too.
Share your Carver experiences, share marine life. Donate when you can but post what your Carver adds to your life too!
Post Reply